Clik here to view.
Synergy Flashloader Utility BCH error "Indexing Error Slot "
For my application's purpose, I am creating a single slot bootloader and following the Custom Flashloader guide for "USB CDC Non-blocking". I have the following settings used with the PK-S5D9 Board:...
View ArticleCAN initialized error occurred while CAN and SCI driver initialized in the...
hi,as title.I refer "an-r11an0065eu0101-synergy-can-hal-mod-guide", and "r11an0085eu0101-synergy-sci-uart-hal-mod-guide".CAN or SCI function works independently,but when I new a thread then add CAN and...
View ArticleClik here to view.
R11AN0336EU0100 mqtt tls via AWS , unable to control LED ON/OFF
Hi , everyone i imported a project regarding mqtt tls . I manage to connect it to AWS and is able to receive the sensor result as shown in the picture belowHowever , when i want to publish the MQTT...
View ArticleNetX™ Telnet Server Module Guide - Application Project
Hi all, I'm currently trying to replicate the (NetX™ Telnet Server Module Guide - Application Project) availabe on the renesas website.I imported the project "NETXDUO_TELNET_SERVER_MG_AP.zip" and ran...
View ArticleS7G2 block media on sd card
This is returning fx_ret_val =144 fx_ret_val = fx_media_open (&g_fx_media0, (CHAR *) "g_fx_media0", SF_EL_FX_BlockDriver, &g_sf_el_fx0_cfg,...
View ArticleWebserver with NETX: Further Examples code?
Hi @all!I'm trying to figure out a way how to implement a small webserver. The example code given by Renesas is that rudimentary that I'm not able to fully understand how to enhance the functionality...
View ArticleContinuous Mode For ADC Data
Hi,I Have Required to Convert the 5 analog data into digital.so I have Required Continuous Mode in ADC.Any one can help me how i can read data or give me the reference code related to Continuous...
View ArticleUSB Mass Storage working only with the prebuilt lib, and not from USBX Source
Hello, I am testing the USBX_Mass_Storage_Host for S7G2 DK board with SSP 1.5.3. The example is working as expected. However, if I enable the USBX Source in the configuration, to not use the libux.a...
View ArticleClik here to view.
Pull-Up Resistors on Data-IO Pins (Flash and SDRAM)
Hello,I´m using the Synergy DK-S7G2 Development kit and i have a question about it.Can someone please explain me the reason, why all the data-Pins of the SDRAM and FLASH have pullup Resistors? Can i do...
View ArticleUSB Boot Monitor
Hi everybody,I have successfully started the device in USB Boot mode with the MD-pin set to low while resetting. I can flash it with the Renesas Flash Programmer, no problem. However, I always need to...
View ArticleProblems importing S7SK_G3PLC_Demo into e2studio
Hi, I'm trying to include the "S7SK_G3PLC_Demo" project (downloaded from the Synergy Gallery with the SynergyPLCFramework_v1.10.zip) into the e2studio.I've been following the steps described in the...
View ArticleReference code of ADC
Hii,Any one can give me the reference code of continuous mode and Group mode In ADC. I have required this code for my project.
View ArticleYROTATE-IT-S5D9 doesn't compile with SSP 1.5.3
Hello everybodyI have one problem (at least... we'll see after this): I'm making my own driver of BrushLess motor with S5D9 and I started with YROTATE-IT-S5D9 kit. This evaluation kit works...
View ArticleWorking application failes when adding ThreadX source
HiI have a newlly started application on an SK-S7G2 starter kit, practically a simple extension of the netx duo http server example. The application works fine so far.I have reached to the point that...
View ArticleMODULATION NEAR 0%-100% DUTY IN TRIANGLE WAVE COMPLEMENTARY PWM WITH...
MODULATION NEAR 0%-100% DUTY IN TRIANGLE WAVE COMPLEMENTARY PWM: in the old Renesas micro SH7044I need to replace when one output is at 0% and the complementary output have (2*dead_time) off time, is...
View ArticleAndroid Open Accessory example availability?
Hi,from where I find example of AOA (Android Open Accessory) protocol implementation for Synergy?The protocol requires the Synergy device to operate in USB host mode. This is supported by USBx...
View ArticleForcing External SDRAM Bus Signal Low
Hello,I'm working with an R7FS7G27H3A01CFC processor and using SSP 1.5.0-rc.1 as well as ThreadX and need to force my SDRAM into power down mode to save on current (the part uses 20mA when active doing...
View ArticleClik here to view.
Unable to set GPIO Port0 001 pin(P001) to high and low in TB S1JA
When i tried to set Port 0 pin 1 (P001) to high it was not Rising to high or low i have tried using API and by setting register directly , Only this pin is not functioning properly remaining pins works...
View Articleriic issue
Hi, my design is using a I2C bus master (IIC channel 1) to comunicate with 4 I2C slaves. I am using 4 instances of the sf_i2c framework, one to each slave. Everything works fine until an error (any...
View Article"Fatal Error: File Not Found" can't be resolved
Hi everyone, I'm trying to export Bacnet DEMO Project into SSP 1.4.0 and have encountered problems about Include and Path. I have the following error: "fatal error: '... .h' not found"I check on the...
View Article