HOW TO TURN OFF THE TASK SCHEDULER (Critical Section)
Hello Everyone, In Start to study the ThreadX RTOS a few month ago and i came across with a thrick situation?In my application I have one thread to execute some routines ( PWM, AD...), and another...
View ArticleSPI issue with data receive
HiAm working on SPI with master and slave devices.Master side is S7G2-DK board and slave is S7G2-SK boardWhen i send a single byte data, data transfer is proper and it is received properly at slaveBut...
View Articleprint NXD udp packet
Hello Dear All, I want to send udp package by using nxd(I mean ip layer uses ipv6). Are there any way to print both payload and udp headers. And also Can I connect my S5D9 PK board to my PC directly...
View ArticleNetX FTP client, retrieving large files from server problem
Hi,I am looking for a code snippet for reading large files from a FileZilla server. The example in the guide doesn't cover retrieval of files that exceed the available packet pool. As I understand from...
View ArticleProblems implementing USB composite device
I'm trying to create a composite device with a CDC-ACM stack and a USBX Mass Storage stack. I've have gotten each to work individually, but when I try to use both in same thread, I get compilation...
View ArticleNetX Duo dhcp server share same ip instance with dhcp client on SSP 1.4.0
Hi all, I'd like to implement a multi-role which contains dhcp server and client on S5,should I create only one IP instance for both sharing or independent two for each role?I create one for sharing...
View ArticleChange UART parity and stop bit at run-time
Hi all,I have a requirement where I need to change baud rate, parity and stop bits of UART in run-time.I know that I can change baud rate using UART API.But how I can change parity and stop bits?Board:...
View Articlespi
HiAm working on SPI with s7g2-dk as master and sk as slave.When i use read api and write api on slave side and master side, its not workingBut when i use writeread api , it works.Actually on slave side...
View ArticleVPN tunneling example
Hello everybodyI need to implement a tunneling mode between 2 devices.Does Renesas work on an IPsec tunneling (Layer 3) ?Does someone has an example ?Thanks
View ArticleSPI slave and master
Hi Am working on SPi with DK baord as master and sk as slave.Both the codes are in while loop but on slave side i get the data only once.How to make it to wait till the master sends the data and read...
View ArticleClik here to view.
NX_FTP_SERVER_MG_AP
Hi to all,I'm using the sample demo an-r11an0273eu0100-synergy-nxd-ftp-server-mod-guide with e2Studio 6.2 on SK-S7G2 and FileZilla 3.33.0 as client. The server starts and I can see it under FileZilla...
View ArticleClik here to view.
Hardfault on network initialization
Dear,I upgraded a synergy ThreadX project from Renesas SSP 1.2 to SSP 1.4,All is fine except the network initialization.I get a Hardfault when the SSP call nx_ip_create function.I can't debug the...
View Articlehow to find NX_REC while using nx_ether_send for sending raw ethernet frames?
HiI am trying to send raw ethernet frames from S5D9 board. I am trying to use the nx_renesas_synergy.c file which contains ethernet drivers.while sending the raw ethernet packet i use nx_ether_send (...
View ArticleMemory usage in S7G2-DK
Hi,I want to know the Memory usage in my synergy renesas project.Am using S7G2-DK board. From one of the link mentioned below i got some information about RAM and ROM...
View ArticleTwo IP instances in a thread on SSP 1.4.0.
Hi, I have a trouble adding two IP instances in a thread,one is for WiFi AP mode and another is for WiFi client mode,when AP mode is on, my phone can detect the WiFi signal but it always goes...
View ArticleNX_CALLer_Error while using NX_ip_raw_packet_Send
Hi, While using nx_ip_raw_packet_Send i am getting error 17 (0x11) which says in documentation invalid caller of this service.What does that mean? in the thread i have a DHCP server, two packet pools...
View ArticleClik here to view.
DMA Examples
Hi Guys, I need an example of getting the DMA working in block mode. I am of course doing a display driver and need to transfer 320x240x2 bytes to the display. I did what seems logical: Dragged in...
View ArticleS128 UART Driver SSP_ERR_IN_USE
HelloI often receive a SSP_ERR_IN_USE when I send data with the UART driver write command, with the driver not the framework, I've faced it with SSP 1.3.3 and 1.4.0. I've simplified my program and...
View ArticlePERIODIC EVENTS USING GUIX SYSTEM TIMER
Hello everyone, I have a few concern about the GUIX system timer and I would be grateful if you guys could help me.In my application I have the GUIX framework running, and inside it I have to two...
View ArticleThermal printer
Can anyone help me plz with some explanation ..how threadx is used in thermal printer like creation of tasks ,in multitasking ..and when and how the cheduling ,intertask communication and intertask...
View Article